---
title: ESXi-Hypervisor-ISO
slug: bhdo/quickstart-guide/installation-and-deployments/iso-installation-on-hypervisors/esxi-hypervisor-iso
createdAt: 2022-04-13T20:08:30.000Z
---

You can install Belden Horizon Data Operations on a virtual machine using VMWare ESXi - Hypervisor. The virtual machine that runs Belden Horizon Data Operations uses the system time of the host environment. To ensure that timestamps of collected data are as universal as possible, we recommend setting the system time of the host environment to the UTC time zone.

A typical Belden Horizon Data Operations virtual file for ESXi deployment adheres to a naming convention as follows: **\<product>-std\_3.1.5.0-amd64.iso**.&#x20;

# Before You Begin                                                                                                                                                                                                                                            &#x20;

:::ExpandableHeading{isOpen="true"}
<u>ESXi Pre-Installation Checklist</u>

- [ ] Prepare your ESXi environment for running virtualization. See [VMware](https://www.vmware.com/worldwide.html) for more information.
- [ ] Set the correct system time on the host environment to prevent any license activation issues. **UTC** is recommended.
- [ ] The virtual machine will run on the same physical network card as the host environment. To ensure that the device can communicate with data sources such as a PLC, DCS, or CNC and can be accessed through the Web UI, make sure that communication can be established.
:::



- Verify your virtual machine can install Belden Horizon Data Operations. See [Verified VM Versions](https://public-docs.litmus.io/bhdo/verified-vm-versions) for more information.&#x20;
- Adjust the system clock for the host environment prior to installing Belden Horizon Data Operations. The 15-day trial period may be rejected and invalidated by the license server if the system clock is not adjusted. If this happens, contact your Belden representative.
- Obtain a valid file in the ISO format from Belden.

To use ESXi-Hypervisor-ISO to install Belden Horizon Data Operations, you will need to do the following.&#x20;

- Step 1: Create a Virtual Machine
- Step 2: Log in to Belden Horizon Data Operations

To jump to a specific section, refer to the Table of Contents on the right side and click the corresponding step.&#x20;

# Step 1: Create a Virtual Machine

You will first need to create the virtual machine that will run Belden Horizon Data Operations.&#x20;

**To install the ESXi-Hypervisor virtual machine:**

1. Start the VMWare application (for example, VMWare vSphere 6.7.0 Update 2 hypervisor).
   The VMWare ESXi application appears.

   ::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/eaoN_NfLc-N7lNsgnKeSP_01l1qe23vfpm0jufvc45azvmware-esxi-hypervisor-app.png" size="80" width="1519" height="276" caption="ESXi Application window" position="center" showCaption="true"}
2. From the left panel, select **Virtual Machines**.
3. Click **Create/Register VM**.
   The *New virtual machine wizard > Select creation type* window appears.

## Select Creation Type

Select **Create a new virtual machine** and click **Next**.&#x20;

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/Ai_VcCP_U84et6rBPDgTw_02tyxtalj5puatejerctgqsimage.png" size="80" width="1163" height="719" caption="Select creation type screen" position="center" showCaption="true"}

## Select a Name and Guest OS

This section allows you to provide a name for the virtual machine and identify the guest operating system.&#x20;

Enter the details for the name and guest OS.&#x20;

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/sd71Fogpc-D_8X5nBD7Hx_03ujvx7krxx6i39eob4bhtbimage.png" size="80" width="1161" height="730" caption="Name and guest OS" position="center" showCaption="true"}

- **Name**: Enter a name for the virtual machine.&#x20;
- **Compatibility**: Your selection must be compatible with your ESXi version Guest OS family (Linux).
- **Guest OS family**: The operating system is based on Linux.
- **Guest OS version**: The kernel used for the operating system is a 64-bit Yocto Kernel.

## Select Storage

You will need to select a datastore for the virtual machine's configuration files and all of its virtual disks.&#x20;

Select a datastore and click **Next**.&#x20;

:::hint{type="info"}
**Note:** The datastore must have at least 40-50 GB of free capacity.
:::

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/AQbPSIhsDzlL3oqsYoF3g_04dmp0yordjzcla2jfvfkdimage.png" size="80" width="1163" height="726" caption="Select storage screen" position="center" showCaption="true"}

## Customize Settings

You will need to configure the virtual machine hardware and virtual machine additional options.&#x20;

Configure the *Virtual Hardware* parameters.&#x20;

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/PhPonIdjpfRlUoViMSybO_05wo-ce0lmzfo6nbiamlulnimage.png" size="80" width="1170" height="699" caption="Customize settings screen" position="center" showCaption="true"}

### CPU parameter

Select **4**. This value is recommended to improve the performance of the VM. If the host system permits or the VM is a production deployment, more cores should be allocated.

### Memory parameter

Enter **8** GB or set the memory size to the desired allocation. At least 2048 MB should be allocated to prevent significant reduction in performance. If the host system permits, more memory is better.

### Hard disk 1 parameter

**To configure the hard disk:**

1. Enter a minimum of **25** GB in the *Hard disk* field.&#x20;
   The minimum file size must be 16 GB to allow the VM to run. The 16 GB value provides the VM with about 2 GB data storage. For a small-scale PoC without much data storage, 8 GB is enough. If this VM is deployed as a production system or the PoC requires a lot of storage for databases, increase the file size beyond 16 GB.
2. Expand **Hard Drive**.
3. From the *Controller location* drop-down list, select **SATA controller 0**.
   The controller has to be designated as SATA or the VM will not boot. If no SATA controller is available,    contact your IT department for assistance.
4. Delete **SCSI Controller 0** and **USB Controller 1&#x20;**&#x61;s they are not needed.&#x20;

:::hint{type="info"}
**Notes:**

- By default, VMs are defined with two network cards. They are configured for the first network card as a Bridged Network and the second network card as NAT.
- Based on the ESXi host environment, if a NAT network exists, a second network adapter must be added and set to NAT.
- If a NAT network exists, move to the next section. Otherwise, skip it.
:::

### Network Adapter 1 parameter

**To confirm the network adapter:**

1. Click **Add network adapter**.
2. From the *New Network Adapter* drop-down list, select **NAT Network**.

### CD/DVD Drive 1 parameter

**To configure the CD/DVD Drive:**

1. From the *CD / DVD Drive 1* drop-down list, select **Datastore ISO file**.
   The *Datastore&#x20;*&#x62;rowser appears.
2. Select the ISO file, and then click **Select**.
3. Click **Next**.
   The *New virtual machine wizard > Ready to complete* window appears.

Review the *Settings&#x20;*&#x61;nd click **Back&#x20;**&#x74;o return to the *Customize settings* screen.&#x20;

Configure the *VM Options* parameters.&#x20;

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/_E0BzCHSw3ns5mr5xgnWV_06dzxeziqfmomu48gttr-sdimage.png" size="80" width="1161" height="695" caption="The VM Options section" position="center" showCaption="true"}

**To configure the VM options:**

1. Select the **VM Options** tab.
2. Expand **Boot Options** and select **BIOS** from the *Firmware&#x20;*&#x64;rop-down list. BIOS is needed for the installer to load.&#x20;
3. Click **Next**.&#x20;
4. Click **Finish**.&#x20;
   The new virtual machine link appears in the Virtual Machine list.
5. Click the new virtual machine link.
   The virtual machine details pane appears.
6. Click the Terminal shell to start the virtual machine.
   Some errors appear in the terminal window. These are warnings and can be ignored for now.&#x20;

The *Welcome to Operating System Installer* appears in the Terminal shell.&#x20;

## Configure Operating System Installer

**To configure the operating system installer:**

1. From the *Welcome to Operating System Installer* screen, enter `yes` and press **ENTER**.
   &#x20;*Select a drive to Install (sda)* appears.
2. Enter `sda` and press **ENTER**.
   *To Confirm Installation and format partitions* appears.
3. Enter `yes` and press **ENTER**.
   The installation begins. During the installation, another error appears regarding an invalid partition table. This is also a warning and can be ignored.&#x20;
4. When the installation completes, close the terminal shell.
5. From the *virtual machine details* pane, click **Edit**.&#x20;
   The *Edit settings* dialog box appears.
6. Select the **VM Options** tab.
7. Expand **Boot Options** and select **EFI&#x20;**&#x66;rom the **Firmware** drop-down list.
8. Click **Save**.
   The virtual machine details pane appears.
9. Click **Power on**, and then click the **Terminal** shell.
   The *Welcome&#x20;*&#x77;indow appears.
10. Note the IP address required for log in.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/KSTdJbgKl8EDt-dOInkuy_image.png" size="80" width="1086" height="795" caption="Terminal User Interface" position="center" showCaption="true"}

# Step 2: Log in to Belden Horizon Data Operations

- See [Access the Belden Horizon Data Operations Web UI](https://public-docs.litmus.io/bhdo/access-the-belden-horizon-data-operations-web-ui) for details on logging in. &#x20;
- See [Access the Terminal User Interface](https://public-docs.litmus.io/bhdo/access-the-terminal-user-interface) for instructions on how to navigate and log in for the first time.

