---
title: Virtual Machine Installation (ESXi-Hypervisor)
slug: bhdm/virtual-machine-installation-esxi-hypervisor
createdAt: 2022-07-05T18:41:09.000Z
---

You can install Belden Horizon Data Manager on a virtual machine using VMWare ESXi - Hypervisor.

The virtual machine that runs Belden Horizon Data Manager uses the system time of the host environment. To ensure that timestamps of collected data are as universal as possible, we recommend setting the system time of the host environment to the UTC timezone.

A typical Belden Horizon Data Manager virtual file for ESXi deployment adheres to the following naming convention:  `<product-2.2.2>.ova`.&#x20;

Login information is as follows:

- admin
  https\://\<your-ip-address>:8446
  username: admin
  password: admin
- application
  https\://\<your-ip-address>
  username: demo
  password: demo
- key-cloak
  https\://\<your-ip-address>/auth/admin
  username: kadmin
  password: kadmin

# Before You Begin

- Configure the docker bridge network. By default, this installation allocates the subnet `172.17.0.0/16`. Make sure that this does not conflict with your host environment network configuration.

:::hint{type="success"}
**Tip**: To reconfigure the docker bridge network, please refer to this [docker guide](https://docs.docker.com/network/bridge/).
:::



- Set up proxies to access Belden Horizon Data Manager behind the company firewall.
- Install ESXi v6.7 or higher. See [VMware](https://www.vmware.com/worldwide.html) for more information.
- Obtain a valid `.ova` file from Belden.&#x20;

To use ESXi-Hypervisor to install Belden Horizon Data Manager, you will need to do the following.&#x20;

- Step 1: Install the Virtual Machine (ESXi-Hypervisor)
- Step 2: Log in to the Belden Horizon Data Manager UI
- Step 3: Verify Post-Installation Checklist

To jump to a specific section, refer to the Table of Contents on the right side and click the corresponding step.&#x20;

# Step 1: Install the Virtual Machine (ESXi-Hypervisor)

You will first need to install the virtual machine that will run Belden Horizon Data Manager.

**To install the virtual machine:**

1\. Start the **VMWare application** (for example, VMWare vSphere 6.7 hypervisor).
The *VMWare ESXi* application appears.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/QX5i3l_Fd6AWRm6JpnloJ_vmware-esxi-hypervisor-app.png" size="80" width="750" height="230" caption="VMWare ESXI panel" position="center" showCaption="true"}

2\. Click **Create/Register VM**.
The *New virtual machine* wizard - *select creation type* appears.

3\. Click **Deploy a virtual machine from OVF or OVA file**, and then click **Next**.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/FS566BPOdjX6VNItvvzAI_vmware-esxi-hypervisor-deploy.png" size="80" width="752" height="400" caption="Select creation type panel" position="center" showCaption="true"}

The *New virtual machine* wizard - *select OVF and VMDK files* appears.

4\. From the right pane, do the following:

&#x20;    a. Enter a name in the **Name** field.

&#x20;    b. Select the `.ova` file using Browse or drag and drop the file on the **Select File** field, and then&#x20;
&#x20;    click **Next**.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/QPfmVPg9vdizkVrF6-kWk_vmware-esxi-hypervisor-select-ova.png" size="80" width="750" height="567" caption="Select OVF and VMDK files panel" position="center" showCaption="true"}

The *New Virtual Machine* wizard - *Select datastore* appears.

5\. From the right pane, select the datastore, and the click **Next**.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/kd3o0r-Bq3vf-JdBwx93B_vmware-esxi-hypervisor-datastore-1.png" size="80" width="752" height="485" caption="Select storage panel" position="center" showCaption="true"}

:::hint{type="info"}
**Note**: The datastore must have at least 80 GB of free capacity.
:::

The *New virtual machine* wizard - *Deployment options* appears.

6\. From the right pane, do the following:

&#x20;    a. Verify that the *VM Network* is set to your main **Network** port group (for example, VM Network).

&#x20;    b. Uncheck **Power on automatically**, and then click **Next**.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/envXsx7gtJ89iM70ghKsE_vmware-esxi-hypervisor-deployment-options.png" size="80" width="751" height="412" caption="Deployment options panel" position="center" showCaption="true"}

The *New virtual machine* wizard - *Ready to complete* pane appears.

7\. Review the settings, and then click **Finish**.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/JK0WdfH0JwlfVlA91f5Va_vmware-esxi-hypervisor-finish.png" size="80" width="748" height="417" caption="Ready to complete panel" position="center" showCaption="true"}

The virtual machine deploys. The progress of the deployment is indicated at the bottom in the *Recent* tasks display.

Deployment may take several minutes.

The virtual machine appears in the localhost pane.

::Image[]{src="https://api.archbee.com/api/optimize/SSUUxKZUk9bFTEPNn_6Zo/ISL62wEOcvyogDdBgZKli_vmware-esxi-hypervisor-localhost.png" size="80" width="747" height="481" caption="Finished Virtual Machine with LEM" position="center" showCaption="true"}

The virtual machine starts up and the terminal window displays.

:::hint{type="success"}
**Tip**:
You can change your settings using the Terminal User interface (TUI).

To log in using the Terminal window, use the following credentials:

username: `em_setup`

password: `edgemanager`
:::

8\. Note the IP address required for login.

# Step 2: Log in to the Belden Horizon Data Manager (BHDM) UI

After installing the virtual machine, you can then log in to Belden Horizon Data Manager using a browser.

**To log in to BHDM UI:**

1\. Open a new incognito browser window, and paste the IP address into the **URL** field.
The application initializes, and then the *Log In* screen appears.

2\. Log in with the following credentials:

-  **Username**: `demo  `
- **Password**: `demo`

3\. Change your password to activate your account, and then click **Submit**.
The *Belden Horizon Data Manager* application opens.

:::hint{type="info"}
**Note**: You must change your password after the first log in.
:::

# Step 3: Verify Post-Installation Checklist

Verify the contents within the [Post-Installation Checklist](https://public-docs.litmus.io/bhdm/post-installation-checklist).

